Seamless gutters, leaf guard, and downspouts installed by local roofers

Gutter Installation Conroe TX Built for Texas Storms

When you need gutter installation Conroe TX homeowners can count on, our crew runs seamless aluminum on site, sizes every downspout to your roof load, and ties it into your fascia and drip edge so water leaves your foundation alone. We have installed gutters across Montgomery County since 2012, from Woodforest to River Plantation. Free estimates, same-week scheduling.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

Call Now (936) 305-7093 → No spam. No obligation. Just practical help.
Conroe Shield Roofing — your local roof repair team
Careful work. Honest options.
About this service

Gutter Installation Conroe TX Done by Roofers

Gutter installation Conroe TX is the measured fabrication and fastening of a roof drainage system: seamless aluminum or steel runs formed on your driveway, hangers screwed into solid fascia boards, downspouts routed to grade, and end caps, miters, and outlets sealed with gutter sealant. We check the drip edge and underlayment line first, because gutters that hang below a short drip edge catch water off the roof edge and dump it behind the gutter instead of into it.

Conroe sits in a heavy-rain corridor. Storms roll through Montgomery County with 2 to 4 inches in an afternoon, and the clay-heavy soil around older Downtown Conroe homes swells and shifts. A rain gutter install Conroe TX property owners schedule before the spring storm season keeps thousands of gallons off the foundation, out of the flower beds, and away from fascia boards that rot fast when they stay wet. If you have been searching gutter installation near me Conroe TX after a storm, we can usually get eyes on it within a few days.

  • ✓ Foundation Water Control
  • ✓ No More Fascia Rot
  • ✓ Seamless Runs, Fewer Leaks
  • ✓ Leaf Guard Keeps Them Clear
What's included

What Is Included in Gutter Installation in Conroe TX

Every quote covers the full install: tear-off, fascia check, seamless forming on site, hangers, downspouts, sealant, and a water test. Add-ons like leaf guard, fascia replacement, and buried downspout extensions are priced separately so you can see exactly what each one costs before you decide.

✓

Tear-Off and Disposal

We remove the old gutters, hangers, and spikes, then haul everything off. You do not rent a dumpster or make a trip to the landfill. If the old system is salvageable and you only need repair, we tell you that instead of selling a full replacement.

✓

Seamless Forming On Site

A seamless gutter machine runs on our truck. Each run is formed to your exact measurement, often 40 to 60 feet with no mid-run seams. Fewer seams means fewer leak points. We form on your driveway, so there is no factory lead time.

✓

Hangers and Fastening

Hangers go in at 24-inch centers, screwed into solid fascia, not nailed. Steep-pitch runs and high-wind areas get 12-inch spacing. We pitch every run toward the downspout at roughly 1/16 inch per foot so water moves instead of sitting.

✓

Downspouts and Discharge

Downspouts are sized to the roof area, strapped to the wall, and extended to grade with splash blocks or buried extensions. Discharge lands 4 to 6 feet from the slab. You tell us where you want the water to go, and we route it there.

✓

Sealant and Water Test

Corners, outlets, and end caps get gutter sealant, not caulk. Then we run a hose through every run and watch the joints and downspouts. If anything weeps or backs up, we fix it before we pack the truck. You see the test happen.

✓

Fascia and Soffit Inspection

Before anything new goes up, we check fascia boards and soffit boards with a moisture meter. Soft wood gets replaced and sealed. Hanging new gutters on rotted fascia is the number one reason gutters pull loose within a year, so we do not skip it.

How it works

What Our Gutter Installation Process Looks Like

01

On-Site Measure

We walk the roofline, measure every run, count downspout drops, and check the fascia boards and soffit boards for rot with a moisture meter. You get a written quote with linear footage, gutter size, downspout count, and guard options. This visit takes 30 to 45 minutes.

02

Material Selection

You pick the profile: 5-inch or 6-inch K-style, or half-round on older homes. Aluminum in 20-plus colors is standard; steel and copper are available. We match your trim or go with a contrasting color, and we confirm downspout placement so discharge lands where you want it.

03

Tear-Off and Fascia Check

Old gutters come down, and we pull the hangers and spikes. If fascia boards are soft, we replace that section before anything new goes up. Hanging new gutters on rotted wood is a callback waiting to happen, so we fix it while the wall is open.

04

Seamless Forming and Hang

A seamless gutter machine runs on our truck. We form each piece to length on site, then set hangers every 24 inches, pitch the run toward the downspout at roughly 1/16 inch per foot, and fasten through the drip edge line so water enters the channel cleanly.

05

Downspouts and Water Test

Downspouts get fastened with straps, extended to grade, and fitted with splash blocks or buried extensions. Then we run water through every run and watch the outlets. If a joint weeps or a downspout backs up, we fix it before we leave the driveway.

Tools & methods

Tools and Methods We Use on Gutter Jobs

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Seamless Gutter Machine

Forms aluminum coil into continuous runs on site. Each piece is cut to your exact measurement, so a 50-foot run has no mid-run seams. This is the single biggest difference between seamless and box-store gutters.

Moisture Meter

Checks fascia boards and soffit boards for hidden rot before we hang anything. A board that looks fine can be soft inside. If the meter reads high, we replace that section.

Ladder and Safety Harness

Two-story and steep-pitch work gets a harness anchored to the roof, not just a ladder. OSHA 10 training covers fall protection, and we follow it on every job, not just the tall ones.

Caulking Gun and Gutter Sealant

Seals corners, outlets, and end caps. We use gutter sealant, not general-purpose caulk, because it stays flexible through Texas heat cycles and does not crack at the joint.

Pry Bar and Hammer

Removes old hangers and spikes without tearing up the fascia. Careful tear-off matters: a pry bar in the wrong spot splits the board, and then you are replacing fascia you did not need to touch.

Utility Knife

Trims sealant, cuts downspout sections to length, and cleans up edges. Small tool, but it is the difference between a finished joint and a smeared one.

Drone

Flies the roofline on two-story homes and steep pitches to check the drip edge, flashing, and gutter line without putting anyone on the roof unnecessarily. You get photos with the quote.

Real results

Before and after.

Sagging Gutters Replaced in River Plantation

Before

A 1990s home with original 5-inch aluminum gutters sagging in three places. Hangers were spaced 36 inches apart, and two sections of fascia were soft from years of overflow. Water pooled at the foundation after every storm.

After

We replaced 12 feet of rotted fascia, formed 148 feet of seamless 6-inch aluminum on site, and set hangers at 24-inch centers. Downspouts went from two to four, routed 5 feet from the slab. A 3-inch rain two weeks later stayed in the system.

Leaf Guard Install on a Woodforest Two-Story

Before

A two-story home with steep pitches and long runs, surrounded by pines. The homeowner was cleaning gutters monthly and still getting overflow at the front corner. The drip edge was short, so water ran behind the gutter instead of into it.

After

We corrected the drip edge, formed 210 feet of seamless 6-inch aluminum, and installed hooded leaf guard on every run. Downspouts were upsized to 3x4 and extended 6 feet from the foundation. The front corner overflow stopped completely.

Storm Damage Replacement in Downtown Conroe

Before

A spring storm bent two gutter runs and ripped a downspout off the wall. The roof also lost shingles at the eave, and water was hitting the siding. The homeowner needed both the roof and the gutters documented for insurance.

After

We documented the damage with photos, repaired the shingle roof at the eave, and replaced 96 feet of seamless aluminum gutter with new hangers and downspouts. The claim covered both the roof and gutter work. Everything was done in two days.

Problems we solve

Gutter Problems We Solve for Conroe Homeowners

Most gutter calls start with one of these four symptoms. Each one has a cause, and each cause has a fix that lasts longer than a bucket under the drip.

Ask a pro →
01

Water pooling at the foundation after every storm

We size the gutter and downspout count to your actual roof area, then route discharge 4 to 6 feet from the slab. On homes where the grade slopes back toward the house, we add buried extensions to move water to a safe spot. The foundation stops seeing the runoff.

↗
02

Gutters sagging and pulling away from the fascia

We pull the old hangers, inspect the fascia with a moisture meter, and replace any soft sections before hanging. New hangers go in at 24-inch centers, screwed into solid wood. On long runs we add hangers at 12 inches to handle Texas heat expansion.

↗
03

Overflowing gutters during heavy rain

We measure roof area per run and upsize to 6-inch channel and 3x4 downspouts where the math calls for it. If leaf guard is the right call, we install a hooded cover that sheds debris while water wicks into the channel. Overflow stops.

↗
04

Downspouts dumping water right at the wall

We extend every downspout to grade and add splash blocks or buried extensions that carry water 4 to 6 feet out. Where the yard slopes back, we run the extension to a pop-up emitter at a low spot. You choose the discharge point, and we make it work.

↗
Proof you can check

Licensed, Insured, and Local Since 2012

✓
GAF Master EliteGAF
✓
Owens Corning PreferredOwens Corning
✓
HAAG Certified InspectorHAAG
✓
NRCA MemberNational Roofing Contractors Association
✓
OSHA 10Occupational Safety and Health Administration
Customer reviews

What Conroe Customers Say About Our Gutter Work

★★★★★
“Our old gutters were sagging and dumping water right at the foundation. Conroe Shield measured everything, showed me the rotted fascia, and replaced it before hanging the new seamless runs. One day, done. We got 4 inches of rain two weeks later and not a drop hit the flower beds. Worth every dollar.”
MT

Marcus T.Homeowner, River Plantation

✓ Verified
★★★★★
“We manage several rentals near downtown and needed gutters on two of them fast. They quoted in writing, showed up when they said, and had both houses done in two days. Downspouts were routed exactly where I asked. I have used them three times since for gutter repair and roof work.”
RP

Ray P.Property Manager, Downtown Conroe

✓ Verified
Good questions

Frequently Asked Questions

(936) 305-7093 →

Most single-story homes in Conroe run $1,200 to $2,800 for seamless aluminum, installed. Two-story homes and long runs push $2,500 to $4,500. Leaf guard adds roughly $3 to $6 per linear foot. Linear footage, stories, gutter size, downspout count, and whether fascia boards need replacement drive the number. We quote in writing after measuring.

A typical single-story home takes 4 to 7 hours, done in one day. Two-story homes, steep pitches, and jobs with fascia rot run into a second day. We form seamless runs on site, so there is no waiting on a factory order. You get a start window the day before, and we text when the crew is rolling.

We do. Conroe Shield Roofing has installed gutters and roofing across Montgomery County since 2012, with crews working out of Conroe daily. We cover ZIP codes 77301, 77303, 77304, 77305, and 77384, plus Willis, Montgomery, Magnolia, Porter, and New Caney. Call (936) 305-7093 and we will get you on the schedule.

The quote covers tear-off and disposal of the old gutters, fascia inspection, seamless forming on site, hangers at 24-inch centers, downspouts, end caps, outlets, sealant, and a water test on every run. Leaf guard, fascia repair, and buried downspout extensions are priced separately. You get a written scope before we start, and we walk the finished system with you.

Ready when you are

Get Your Gutter Installation Conroe TX Quote This Week

We measure, quote in writing, and form seamless runs on site. Licensed, insured, and 14 years in Montgomery County. Call (936) 305-7093 and we will get you on the schedule before the next storm.

Get Free Estimate (936) 305-7093 →
Request an appointment

Contact Conroe Shield Roofing

Call us at (936) 305-7093 or email info@conroeshieldroofing.com and we will get you scheduled. We answer 24/7 for emergencies and return non-urgent calls the same business day. Free estimates across Conroe and Montgomery County.

Tap to call(936) 305-7093