Seal, protect, and restore your roof without full replacement

Roof Coating Conroe TX That Adds 10-15 Years

Roof coating conroe TX is a seamless protective membrane sprayed or rolled onto your existing roof to stop leaks, lock down granules, and reflect heat. If your shingles are aging but the deck is solid, coating costs a fraction of replacement. We serve homeowners across Montgomery County with roof coating service conroe, Texas trusts for flat roofs, metal, and aging shingle systems.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

Call Now (936) 305-7093 → No spam. No obligation. Just practical help.
Quality Roof Coating in conroe
Careful work. Honest options.
About this service

What Roof Coating Conroe TX Actually Does

Roof coating conroe TX is a fluid-applied membrane that cures into a seamless rubberized layer over your existing roof surface. Unlike tar patches or caulk, coating bonds across the entire field, sealing hairline cracks, flashing edges, and fastener heads in one continuous sheet. We apply it to flat roofs with TPO membrane or modified bitumen, metal roofing panels, and aging asphalt shingles that still have solid decking underneath. The coating fills granule voids, bridges minor ponding areas, and adds a reflective top layer that drops attic temperatures.

Conroe roofs take a beating. Summer surface temps on dark shingles hit 160°F, then afternoon thunderstorms dump two inches in an hour. That expansion and contraction cycle opens seams, pulls flashing, and strips granules year after year. A roof coating application conroe TX homeowners schedule in fall or spring locks the roof down before the next hail season. If you have been searching for roof coating near me conroe TX, we inspect first, tell you honestly whether coating will work, and quote a fixed price before we open a bucket.

  • ✓ Extends Roof Life 10-15 Years
  • ✓ Stops Leaks at the Source
  • ✓ Cuts Attic Heat and Cooling Bills
  • ✓ Avoids Tear-Off and Landfill Waste
What's included

What Is Included in Our Roof Coating Service

Every coating job we run includes the same core scope. We do not strip items out to hit a lower price and then add them back as change orders. Here is what you get when you hire us for roof coating application conroe TX.

✓

Full Roof Inspection and Report

We inspect with a moisture meter and infrared camera, fly a drone for overhead photos, and give you a written report showing what we found. You see the same photos we do, so there is no guesswork about what needs coating and what needs repair.

✓

Pre-Coating Repairs

We replace cracked pipe boots, reseal flashing, re-nail lifted shingles, and repair any active leaks before coating. If we find fascia rot or soffit damage, we handle that too. Coating over broken components wastes money, so we fix them first.

✓

Pressure Washing and Surface Prep

We pressure-wash the full roof at 1,500-2,000 PSI to remove dirt, algae, and loose granules. Then we let it dry completely and treat any moss or algae with a mildicide. Proper prep is why our coatings bond and stay bonded.

✓

Two-Coat Application

We apply a base coat and a build coat using airless sprayers and rollers, reaching 20-30 mils dry thickness. Flashing, vents, and penetrations get brushed by hand. Thickness is checked with a wet-film gauge at multiple points before we leave.

✓

Warranty and Follow-Up

You get the manufacturer warranty on the coating material plus our own workmanship warranty. We schedule a 12-month follow-up inspection at no charge to confirm the coating is performing. If anything is off, we fix it under warranty.

How it works

Our Roof Coating Process, Step by Step

01

Inspection and Assessment

We walk the roof with a moisture meter and infrared camera to find wet decking, soft spots, and active leaks. A drone captures overhead photos of the full field. You get a written report showing exactly what we found, what coating can fix, and what needs repair first. This inspection takes 45-60 minutes and costs nothing.

02

Repairs and Prep

Before any coating goes down, we fix what is broken. That means replacing cracked pipe boots, resealing flashing with roof cement, re-nailing lifted shingles with a roofing nail gun, and clearing debris from gutters and downspouts. If we find fascia rot or soffit damage, we handle it now. Prep is 60-70% of a successful coating job.

03

Surface Cleaning

Coating will not bond to dirt, algae, or loose granules. We pressure-wash the full roof at 1,500-2,000 PSI, then let it dry completely. On shingle roofs, we blow off remaining granules and treat any moss or algae with a mildicide. This step takes 3-5 hours depending on roof size and pitch. We do not rush it.

04

Coating Application

We apply the coating in two passes using airless sprayers and rollers, working from the ridge down. The first pass is a base coat that soaks into the surface. The second is a build coat that reaches 20-30 mils dry thickness. Flashing, vents, and penetrations get brushed by hand. Most residential roofs are coated in one day.

05

Final Inspection and Warranty

We walk the roof again with you, checking thickness at multiple points with a wet-film gauge. You receive photos of the finished job, the manufacturer warranty paperwork, and our own workmanship warranty. We also schedule a 12-month follow-up inspection at no charge to confirm the coating is performing as specified.

Tools & methods

Tools and Methods We Use for Roof Coating

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture Meter and Infrared Camera

We use these to find wet decking and active leaks before coating. Coating over wet decking traps moisture and causes rot, so this step is non-negotiable.

Drone with High-Resolution Camera

We fly the roof to capture overhead photos of the full field. You see exactly what we see, which makes it easy to understand what needs repair and what can be coated.

Airless Sprayer and Rollers

We apply coating with airless sprayers for speed and rollers for control. Sprayers give even coverage across the field; rollers and brushes handle flashing, vents, and edges.

Wet-Film Gauge

We check coating thickness at multiple points during application. The gauge tells us whether we are hitting the 20-30 mil spec that earns the manufacturer warranty.

Pressure Washer (1,500-2,000 PSI)

We pressure-wash the full roof to remove dirt, algae, and loose granules. Coating will not bond to a dirty surface, so this step protects your investment.

Roofing Nail Gun and Pry Bar

We use these for pre-coating repairs, re-nailing lifted shingles and replacing damaged flashing. A roofing shovel handles tear-off of failed sections when needed.

Safety Harness and Ladder

Every crew member wears a safety harness on steep pitches and uses proper ladder technique. OSHA 10 and OSHA 30 training means we work safely, which protects your roof and our crew.

Real results

Before and after.

River Plantation Shingle Roof Restoration

Before

A 1998 shingle roof in River Plantation was losing granules across the south-facing slope. The homeowner had two quotes for full replacement at $13,500 and $15,200. An active flashing leak at the chimney had stained the ceiling in the living room.

After

We repaired the chimney flashing, replaced four cracked pipe boots, and applied a two-coat reflective system over the full roof. Total cost was $6,800. The leak stopped, the ceiling stain was painted over, and the roof passed a buyer's inspection 18 months later.

Downtown Conroe Flat Roof Coating

Before

A 4,200 sq ft commercial flat roof in Downtown Conroe had a TPO membrane that was 14 years old. Seams were opening, ponding was visible after every rain, and the building owner was facing a full tear-off at $38,000.

After

We cleaned the membrane, resealed all seams, repaired two penetrations, and applied a reflective coating at 25 mils. Cost was $16,500. Ponding resolved, surface temps dropped 20°F, and the building's summer cooling load dropped enough to show on the next utility bill.

Panorama Village Metal Roof Rust Stop

Before

A metal roof in Panorama Village had rust spreading from fastener heads across three panels. Two roofing companies recommended replacing the affected panels at $4,800 plus labor. The homeowner wanted to stop the rust without panel replacement.

After

We treated the rust with a converter, replaced 60 fasteners, sealed all seams with roof cement, and coated the full roof with a rust-inhibiting membrane. Cost was $3,200. The rust has not returned, and the roof looks uniform instead of patchy.

Problems we solve

Roof Problems Coating Solves for Conroe Homeowners

Coating is not a cosmetic fix. It solves specific, expensive problems that Conroe roofs develop as they age. Here is what we hear on the phone and how coating addresses it.

Ask a pro →
01

Shingle granule loss leaving bare spots

We coat the roof to lock down remaining granules and seal the exposed mat. The coating becomes the new wear surface, adding 10-15 years of life and stopping the granule loss from getting worse.

↗
02

Flat roof ponding water after storms

We repair the low spots, reseal seams, and apply a reflective coating that sheds water faster. The coating also protects the membrane from UV degradation, which is what makes flat roofs fail in the first place.

↗
03

Metal roof rust at fasteners and seams

We treat the rust, replace failing fasteners, seal seams with roof cement, and coat the entire roof with a rust-inhibiting membrane. The coating stops rust from spreading and adds a decade of service life.

↗
04

Recurring leaks at flashing and pipe boots

We repair or replace the flashing, install new pipe boots, and coat the entire roof surface. The coating encapsulates the repaired areas in a seamless membrane, so there are no edges for water to get under.

↗
Proof you can check

Licensed, Certified, and Warrantied

✓
Texas Roofing LicenseState of Texas
✓
OSHA 10 and OSHA 30Occupational Safety and Health Administration
✓
HAAG Certified InspectorHAAG Engineering
✓
NRCA MemberNational Roofing Contractors Association
✓
Manufacturer-Approved Coating InstallerFirestone, Carlisle, and GAF
Customer reviews

What Conroe Homeowners Say About Our Coating Work

★★★★★
“Our 1990s shingle roof was losing granules fast and we were quoted $14,000 for replacement. Conroe Shield inspected, told us the deck was solid, and coated it for less than half that. Two summers later, no leaks and the attic is noticeably cooler. They fixed two flashing leaks during prep and did not charge extra. Straight shooters.”
MT

Marcus T.Homeowner, River Plantation

✓ Verified
★★★★★
“I had three companies tell me I needed a full tear-off. Conroe Shield was the only one who got on the roof with a moisture meter and showed me the deck was dry. They coated my metal roof, replaced rusted fasteners, and sealed the seams. The rust has not come back and the roof looks new. Honest work at a fair price.”
BK

Bill K.Homeowner, Panorama Village

✓ Verified
Good questions

Frequently Asked Questions About Roof Coating

(936) 305-7093 →

Most residential roof coating jobs in Conroe run $2.50 to $5.50 per square foot in 2026, which puts a typical 1,800-2,200 sq ft roof between $4,500 and $12,000. Flat roofs and metal roofs tend to price lower per square foot than steep shingle roofs because they are faster and safer to coat. Repairs needed before coating add to the total. We quote a fixed price after inspection, so you know the full number before we start.

A properly applied coating lasts 10 to 15 years in this climate. Conroe summers push surface temps past 150°F and hail season runs March through June, so coating takes real abuse. We apply 20-30 mils dry thickness, which is the spec that earns the full warranty. Cheaper thin coatings fail in 5-7 years. We also recommend a recoat at year 10-12 to extend the system another decade without a tear-off.

Conroe Shield Roofing applies roof coating across Conroe and Montgomery County. We have been in business since 2012 and our crews are OSHA-certified and Texas-licensed. We handle flat roofs, metal roofs, and shingle roofs. Call (936) 305-7093 and we will schedule a free inspection. If coating is not the right answer for your roof, we will tell you what is.

Every job includes a full roof inspection with moisture meter and infrared camera, repair of flashing leaks and pipe boots, pressure-washing, two coats of manufacturer-approved coating, and a final thickness check. You get photos, warranty paperwork, and a 12-month follow-up inspection. We also clear gutters and downspouts as part of prep so water drains properly after the coating cures.

Ready when you are

Get Your Roof Coating Conroe TX Quote Today

One free inspection tells you whether coating will save your roof or if replacement is the better call. We quote fixed pricing, use manufacturer-approved systems, and back the work with a written warranty. Call (936) 305-7093 and we will schedule your inspection this week.

Schedule Free Inspection (936) 305-7093 →
Request an appointment

Contact Conroe Shield Roofing

Call us at (936) 305-7093 or email info@conroeshieldroofing.com and we will get you scheduled. We answer 24/7 for emergencies and return non-urgent calls the same business day. Free estimates across Conroe and Montgomery County.

Tap to call(936) 305-7093