We seal chimneys, vents, and valleys before water finds your ceiling

Roof flashing repair conroe TX that stops leaks cold

Roof flashing repair conroe TX is what you call when water shows up where it shouldn't: a stain on the ceiling, a drip in the attic, rust streaks down a chimney. Conroe Shield Roofing has fixed flashing across Montgomery County since 2012. We find the exact entry point, replace the failed metal and sealant, and test it before we leave. One call, one fix, no guesswork.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

Call Now (936) 305-7093 → No spam. No obligation. Just practical help.
Professional Roof Flashing Repair in conroe
Careful work. Honest options.
About this service

What roof flashing repair conroe TX actually involves

Roof flashing repair conroe TX is the work of replacing or resealing the metal that keeps water out of the joints on your roof: chimney edges, vent pipes, skylight frames, wall intersections, and valleys where two roof planes meet. Flashing is thin metal, usually galvanized steel, aluminum, or copper, and it lives in the spots water hits hardest. When the sealant dries out, the metal lifts, or a nail backs out, water gets under your shingles and into the deck. We pull the damaged section, cut new flashing to fit, set it under the shingle course above and over the course below, then seal every seam with roof cement rated for Texas heat.

Most flashing leaks in Conroe start small and get worse fast. A pipe boot cracks after four or five summers of 100-degree attic heat. A chimney flashing pulls loose after a wind event. Water tracks down a rafter and shows up as a ceiling stain ten feet from the actual leak. If you have been searching for roof flashing repair near me conroe TX, the smart move is to get it looked at before the next storm. A $300 flashing fix today beats a $3,000 deck and drywall repair in the spring.

  • ✓ Stop leaks at the source
  • ✓ Save your deck and drywall
  • ✓ Hold up to Texas storms
  • ✓ Protect your warranty
What's included

What our flashing repair service includes

Every flashing repair job includes a full inspection, the repair itself, and a test to prove it works. Here is what you get when you book with us. If we find additional damage during the repair, we show you photos and give you a price before we do any extra work.

✓

Full flashing inspection

We check every flashing point on your roof: chimney, skylights, pipe boots, vents, valleys, wall intersections, and drip edge. We use a moisture meter and infrared camera inside the attic to trace water paths. Inspection takes 45 to 60 minutes.

✓

New flashing material

We cut and install new flashing from galvanized steel, aluminum, or copper depending on your roof type and budget. We match the existing metal when possible. All flashing is installed with proper laps and fastened with roofing nails or screws rated for the material.

✓

Sealant and roof cement

Every seam gets roof cement and a bead of roof sealant rated for Texas heat. We use products that stay flexible from 0 to 180 degrees. Cheap sealant dries out in two summers. We do not use it. Our sealant lasts five to ten years.

✓

Hose test and verification

After the repair, we run water over the area for 10 to 15 minutes while watching from inside the attic. If we see any moisture, we keep working. You get a repair that is tested, not just installed. We do not leave until it is dry.

✓

Cleanup and photo documentation

We magnet-sweep your yard for nails, haul off old flashing and debris, and send you photos of the finished work. You also get a written summary of what was repaired and a 5-year workmanship warranty. Most customers never call us about that spot again.

How it works

How our flashing repair process works

01

Call and schedule

Call (936) 305-7093 or book online. We ask where the leak is showing up, how long it has been happening, and whether you have had recent storm damage. Most Conroe jobs get a same-day or next-day inspection slot. Emergency roof flashing repair conroe TX calls get priority.

02

On-site inspection

A HAAG Certified Inspector walks the roof, checks every flashing point, and uses a moisture meter and infrared camera inside the attic to trace the water path. We photograph everything. You get a written scope with photos before we start. Inspection takes 45 to 60 minutes.

03

Repair or replace

If the flashing is salvageable, we reseal and re-secure it. If the metal is rusted, cracked, or bent, we cut and install new flashing. We use pry bars and roofing shovels to lift shingles without tearing them, then reset them with a roofing nail gun. Most jobs finish in two to five hours.

04

Seal and test

Every seam gets roof cement and a bead of roof sealant. We run a hose test over the repaired area for 10 to 15 minutes while watching from inside the attic. If we see moisture, we keep working until we do not. No leak, no guesswork.

05

Clean up and document

We magnet-sweep the yard for nails, haul off old flashing, and send you photos of the finished work plus a written summary of what was repaired. You get a 5-year workmanship warranty on the flashing repair. Most customers never call us about that spot again.

Tools & methods

Tools and methods we use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture meter

We use a moisture meter to find water inside your walls and attic. It tells us exactly where the leak is, even if the surface looks dry. This is how we trace leaks that show up far from the actual entry point.

Infrared camera

An infrared camera shows temperature differences caused by moisture. We use it to scan the attic and ceiling for hidden water damage. It finds leaks that a visual inspection would miss.

Roofing nail gun

We use a roofing nail gun to reset shingles after flashing repair. It drives nails to the correct depth and angle every time. That means the shingles stay put and the repair holds.

Pry bar and roofing shovel

We use a pry bar and roofing shovel to lift shingles without tearing them. This lets us slide new flashing under the shingle course above and over the course below. No torn shingles, no new leaks.

Caulking gun and roof cement

We use a caulking gun to apply roof cement and sealant to every seam. We use products rated for Texas heat that stay flexible for years. Cheap sealant dries out in two summers. We do not use it.

Safety harness and ladder

Every technician wears a safety harness and uses a ladder rated for the job. We follow OSHA 10 and OSHA 30 safety standards on every roof. That protects our crew and your property.

Real results

Before and after.

Chimney flashing leak in River Plantation

Before

A homeowner in River Plantation had a ceiling stain that kept coming back. Two previous roofers had patched the shingles. We inspected and found the chimney flashing had pulled away from the masonry. Water was running down the chimney and into the attic.

After

We removed the old flashing, installed new step flashing and counter-flashing, and sealed it to the masonry. The repair took five hours and cost $780. The ceiling stain dried out and did not return. The homeowner repainted the ceiling two weeks later.

Pipe boot failure in Downtown Conroe

Before

A Downtown Conroe homeowner had a drip in the laundry room every time it rained. The pipe boot on the roof was cracked and brittle. It had been patched with sealant twice, but the sealant kept failing.

After

We replaced the pipe boot with a new UV-resistant boot sized to the pipe. The repair took two hours and cost $275. We tested it with a hose for 15 minutes. No leak. The homeowner has not had a drip since.

Valley flashing rust in Woodforest

Before

A Woodforest homeowner had water pouring into the attic during heavy rain. The valley flashing was rusted through. The roof was only 12 years old, but the valley had been holding water and the metal had failed.

After

We removed the old valley flashing, installed new metal with ice and water shield underneath, and reset the shingles. The repair took six hours and cost $1,100. We hose-tested it for 15 minutes. Dry. The attic stayed dry through the next storm.

Problems we solve

Flashing problems we fix in Conroe

Flashing fails in predictable ways. Here are the problems we see most often in Conroe and what happens if you ignore them.

Ask a pro →
01

Chimney flashing pulling away from masonry

We remove the old flashing, cut new counter-flashing and step flashing, and seal it to the masonry with masonry-safe sealant. We also check the chimney cap and crown. Most chimney flashing repairs take four to six hours.

↗
02

Cracked pipe boot flashing

We replace the pipe boot with a new one sized to your pipe. We use boots with UV-resistant rubber that lasts longer than the original. The repair takes about two hours and costs $250 to $400.

↗
03

Valley flashing rusted through

We remove the old valley flashing, install new metal with ice and water shield underneath, and reset the shingles. Valley flashing replacement takes four to six hours and runs $600 to $1,200.

↗
04

Skylight flashing leaking at the frame

We remove the old flashing around the skylight, install a new flashing kit, and reseal the frame. If the skylight is damaged, we can replace it. Most skylight flashing repairs take three to five hours.

↗
Proof you can check

Licensed, certified, and reviewed

✓
GAF Master EliteGAF
✓
Owens Corning PreferredOwens Corning
✓
HAAG Certified InspectorHAAG
✓
OSHA 10 and OSHA 30Occupational Safety and Health Administration
✓
NRCA MemberNational Roofing Contractors Association
Customer reviews

What Conroe homeowners say

★★★★★
“We had a ceiling stain for two months and two other roofers told us we needed a full replacement. Conroe Shield found the leak at the chimney flashing in 20 minutes. They repaired it the same day for $480. That was last fall. No leak since. They saved us thousands.”
MR

Mark R.Homeowner, River Plantation

✓ Verified
★★★★★
“Our pipe boot cracked and we had a drip in the laundry room. I found them searching for roof flashing repair near me conroe TX. They came out the next morning, replaced the boot, and tested it with a hose. Charged $275. Fair price, quick work, no mess left behind.”
JT

James T.Homeowner, Downtown Conroe

✓ Verified
Good questions

Frequently Asked Questions

(936) 305-7093 →

Most flashing repairs in Conroe run $250 to $900 in 2026. A simple pipe boot replacement is on the low end. Chimney flashing repair or valley flashing replacement is on the high end. The price depends on roof pitch, height, material, and how much damage the leak caused. We give you a written price before we start. No surprises.

Yes. Most flashing damage is repairable without replacing the roof. If the metal is rusted through or bent, we cut and install new flashing. If the sealant failed but the metal is sound, we clean and reseal it. We inspect first and tell you honestly which one you need. About 80% of the flashing jobs we see are repair, not replacement.

Conroe Shield Roofing repairs flashing across Conroe and Montgomery County. We have been in business since 2012 and hold HAAG Certified Inspector credentials. Call (936) 305-7093 and we will schedule an inspection, usually same-day or next-day. We serve Downtown Conroe, River Plantation, Panorama Village, April Sound, Bentwater, and surrounding areas.

Most flashing repairs take two to five hours from start to finish. A single pipe boot takes about two hours. Chimney flashing repair takes four to six hours because of the detail work and height. We test every repair with a hose before we leave. If we find hidden damage under the shingles, we tell you before we proceed.

Ready when you are

Get your roof flashing repair conroe TX scheduled today

Water is already inside your roof if you are seeing stains or drips. Call Conroe Shield Roofing at (936) 305-7093. We are licensed, insured, and have been fixing flashing in Montgomery County since 2012. Same-day inspections available.

Book Inspection (936) 305-7093 →
Request an appointment

Contact Conroe Shield Roofing

Call us at (936) 305-7093 or email info@conroeshieldroofing.com and we will get you scheduled. We answer 24/7 for emergencies and return non-urgent calls the same business day. Free estimates across Conroe and Montgomery County.

Tap to call(936) 305-7093